|
65 WATTS |
NO MINIMUM ORDER REQUIRED |
|
SRW-65 SERIES |
|
Features
- RoHS
- Universal 85-264 VAC Input
- Compact 4.0" X 6.0" X 1.1" Size
- Class B Emissions Per EN 55022
- 2 Year Warranty
- Fits 1U Application
- EN 60950-1 ITE Certification
- One to Four Outputs
- Optional Chassis & Cover
|
| Total Output Power at 500 C |
65 W |
| Output Voltage Centering |
Output 1: +/-1.0%
Output 2: +/-5.0%
Output 3: +/-5.0%
Output 4: +/-5.0%
(All outputs at 50% load) |
| Source Regulation |
Outputs 1-4: 0.5% |
| Load Regulation |
| Output 1: 1.0% (10-100%Load Change) |
| Output 2: 5.0% (20-80% Load Change) |
| Output 3: 5.0% (20-80% Load Change) |
| Output 4: 5.0% (20-80% Load Change) |
| Cross Regulation |
Output 2: 5.0%
Output 3: 5.0%
Output 4: 5.0%
(Output 1 load varied 50-100%) |
| Output Voltage Adjust Range |
Output 1: 95% to 105% |
| Output Noise |
Outputs 1-4: 1.0% |
| |
|
| Turn On Overshoot |
None |
| Transient Response |
Outputs 1-4 |
| Volt. Deviation |
5.0% |
| Recovery Time |
2 mS |
| Load Change |
50% To 100% |
| Output Overvoltage Protection (Optional) |
Output 1: 110% to 150% |
| Output Overpower Protection |
Output 1-4 110% Min. |
| Outputs cycle on/off, auto recovery |
| Hold Up Time |
16 mS Min, 65 W Output
120 V Inputt |
| Start Up Time |
1 Second | |
| Source Voltage |
85-264 Voltage AC |
| Frequency Range |
47-63 Hz |
| Source Current |
|
| True RMS |
1.5A At 85V Inputut |
| Peak Inrush |
40A |
| Efficiency |
.72 -.80 (Varies by model) | |
| |
ENVIRONMENTAL SPECIFICATIONS |
|
| Ambient Operating Temperature Range |
0oC to +70oC Derating: See Power Rating Chart |
| Ambient Storage Temperature Range |
-40oC to +85oC |
| Temperature Coefficient |
Outputs 1-4: 0.02%/oC |
| Conducted Emissions |
EN 55022 Class B | |
|
|
|
| General |
|
Protection Class: |
I |
| Overvoltage Category: |
II |
| Pollution Degree: |
2 |
 |
Underwriters
Laboratories
File E137708 |
UL 60950-1 First Edition |
|
 |
UL Recognition Mark for Canada
File E137708 |
CAN/CSA-C22.2 No. 60950-1-03 |
|
 |
TUV |
EN 60950-1:2001 |
|
|
|
|
Low Voltage Directive
CB Report per IEC 60950-1(2001) First Edition All National Deviations |
| |
| Dielectric Strength |
|
| Reinforced Insulation |
4242 VDC, Primary to Secondary, 1 Sec. |
| Basic Insulation |
2121 VDC, Primary to Ground, 1 Sec. |
|
Operational Insulation |
500 VDC, Secondary to Ground, 1 Sec |
| Mean Time Between Failures |
150,000 Hours min., MIL-HDBK-217F, 25oC, GB |
|
Weight
Power Fail Signal (Optional) |
1.65 Lbs. Chassis and Cover
0.80 Lbs. Open Frame
Logic low with input power failure, 2mS minimum prior to output 1 dropping 1% | |
| Model |
Output 1 |
Output 2 |
Output 3 |
Output 4 |
| SRW-65-4001 |
+5V/5A |
-5V/3A |
+12V/2A |
-12V/2A |
| SRW-65-4002 |
+5V/5A |
+12V/1A |
+12V/2A |
-12V/2A |
| SRW-65-4003 |
+5V/5A |
+24V/1A |
+12V/2A |
-12V/2A |
| SRW-65-4004 |
+5V/5A |
-5V/3A |
+15V/2A |
-15V/2A |
| SRW-65-4005 |
+5V/5A |
+24V/1A |
+12V/2A |
-5V/2A |
| SRW-65-4006 |
+5V/5A |
+24V/1A |
+15V/2A |
-15V/2A |
| SRW-65-4007 |
+5V/5A |
+26V/1A |
+15V/2A |
-15V/2A |
| SRW-65-4008 |
+5V/5A |
+24V/1A |
+12V/2A |
-12V/2A |
| SRW-65-4009 |
+5V/7.5A |
+48V/.25A |
+15V/1A |
-15V/1A |
| SRW-65-4103 |
+5V/5A |
26V/1A |
+12V/2A |
-12V/2A |
| SRW-65-4104 |
+5V/4A |
5V/.25A |
+15V/2.5A |
24V/.5A |
| SRW-65-3001 |
+5V/5A |
|
+12V/3A |
-12V/1A |
| SRW-65-3002 |
+5V/7A |
|
+12V/2A |
-12V/2A |
| SRW-65-3003 |
+5V/7A |
|
+15V/2A |
-15V/2A |
| SRW-65-3004 |
+5V/5A |
-5V/4A |
+12V/2A |
|
| SRW-65-3005 |
+5V/5A |
-5V/4A |
+24V/1A |
|
| SRW-65-3006 |
+5.25V/6A |
+15V/1A |
+34V/1.5A |
|
| SRW-65-2001 |
+5V/7A |
|
|
-5V/5A |
| SRW-65-2002 |
+5V/7A |
|
+12V/3A |
|
| SRW-65-2003 |
+12V/3A |
|
|
-12V/2.5A |
| SRW-65-2004 |
+15V/2.5A |
|
|
-15V/2A |
| SRW-65-2005 |
+5V/7A |
|
+24V/1.5A |
|
| SRW-65-2006 |
+5V/9A |
|
+12V/2A |
|
| SRW-65-2008 |
+6V/5A |
|
|
-6V/5A |
| SRW-65-1001 |
5V/13A |
|
|
|
| SRW-65-1002 |
12V/5.4A |
|
|
|
| SRW-65-1003 |
15V/4.3A |
|
|
|
| SRW-65-1004 |
24V/2.7A |
|
|
|
|
SRW-65-1005
SRW-65-1006
SRW-65-1104
SRW-65-1105 |
18V/3.6A
24V/3.33A
24V/3.33A
21V/3.1A |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| |
Notes |
| |
Consult factory for alternate output configuration.
Consult factory for positive, negative or floating outputs.
Refer to Application Information for complete output power ratings.
All specifications are maximum at 25C unless otherwise stated and are subjected to change without notice.
Specify optional chassis and cover, power fail, overvoltage protection, transient protection or DC Input when ordering.
TUV only:SRW-65-2008 |
| |
SRW-65 SERIES MECHANICAL SPECIFICATIONS |
| |
|
|
|
|
- Each output can deliver its rated current but total output power must not exceed
65 watts.
- Semiconductor case temperature must not exceed 110 C
- Sufficient area must be provided around convection cooled power supplies to allow natural movement of air develop.
- This product is intended for use as a professionally installed component within information technology and medical equipment.
- A minimum load of 20% is required on output one to insure proper regulation of remaining outputs.
- Peak to peak output ripple and noise is measured directly at the output
terminals of the power supply, without the use of the probe ground lead or retractable tip, 20 MHz bandwidth.
- This product was type tested and safety certificated using the the dielectric strength test voltages listed in Table 5B of UL 60950-1. In consideration of clause 5.2.2, care must be taken to insure the voltage applied to a reinforced insulation does not over stress basic insulation. Secondary to ground capacitors may need to be removed prior to performing a dielectric strength type test on the end product. It is highly recommended that the DC test voltages be used when performing a production-line dielectric strength test of the assembled end product. Please consult factory for further information.
| |
| |
- This power supply has been safety approved and final tested using a DC
dielectric strength test. Please consult factory before performing AC dielectric strength test.
- Maximum screw penetration into mounting holes is .250 inches
|
| |
Maximum Output Power vs. Ambient Temperature |
|
| |
| TB1 |
AC Input |
.156 friction lock header mates with Molex 09-50-3051 or equivalent crimp terminal housing with Molex 08-50-0189 or equivalent crimp terminal. |
| TB2 |
DC Output |
.156 friction lock header mates with Molex 09-50-3101 or equivalent crimp terminal housing with Molex 08-50-0189 or equivalent crimp terminal. |
|
PF |
Optional power fail signal. | G Optional power fail signal return. |
| |
RECOMMENDED AIR FLOW DIRECTION |
- Optimum
- Good
- Fair
| | | |
